Cnc Beam Drill Line Jig

Cnc Beam Drill Line Cutter

".. This machine is designed for Structural fabricators. But I knew it would work well for drilling trucks frames. The assembly was flawless due to the machine's repeatability and accuracy. Avenger drills one channel for a truck in just two hours. We would have taken 16 hours if it was done manually. The machine has increased our productivity AND profitability !.."

Voortman’s Roller Feed Measuring System surpasses the industry standard in roller measurement technology. Accuracy in measurement is vital to avoid any production delays. Even with material deviations, accuracy cannot be compromised.

Voortman built the CNC Drill Line only for GSS Machinery. Voortman manages the installation, warranty, service and maintenance of the CNC Drill Line. Voortman is the service provider. GSS Machinery is available to help if needed.

GSS Machinery's magnetic brush, broom and magnet brush help to remove chips from machines and sweep up chips on the floor.

Cnc Beam Drill Line 2018

Cnc Beam Drill Line 2018

Voortman is known for its dedication to service and support. It is the industry's gold standard. Voortman provides a global team for customer support that is available 24/7 at the Voortman Customer Support Center. Voortman supports you with state-of-the art remote diagnostic software, local field support and an industry-leading warranty.

Z-Reader Probe-The Z-Reader Probe is a device that maps the location of the surface. It can be programmed or manually controlled. It can be disabled while cutting, and it can be pulled out of harm's reach. It can be activated to verify the surface at each pierce prior to cutting, or to drive surface mapping for the entire part before cutting begins. It is used to initialize or zero the device to the desired surface and then tracks or accumulates the difference between that zeroing effort.

Cnc Beam Drill Line Cutter

Quality

The CNC Drill Line is a 100% hydraulic machine making maintenance and parts exceptionally affordable. The CNC Drill Line was designed specifically to be used throughout the world and thus uses only components from major manufacturers, most of which can be sourced in the local market. Voortman keeps all parts on hand for next day delivery in the USA. In most of our overseas countries we offer local service and support.

It is no good having a CNC drilling machine if it doesn’t enable a fabricator compete at the top of the steel fabrication field. Advantage-2 allows you to process technical programmes with speed and intelligence. Each drilling axis includes three five-station tool changers. Each can drill, countersink and tap as well. Signomat underside scribers or part stamping units are also possible to be fitted to this drill-line. Part information is kept even after blasting, painting and galvanizing. Minimizing shop errors? Check. Advantage-2 drills more aggressively and produces more holes than any other line of drilling. High torque drilling axes have thicker, more aggressive cuts that extract more chips with each turn. This drill line can eat through beams as well channel, angle and tube. Advantage-2 is able to process any profile up to 44 inches wide x 18 inches tall.

Quality

Drill Line

I truly believe that without the support provided by the staff and personnel at GSS Machinery we would not be performing in the steel fabrication markets that we now enviably find ourselves competing in..”

The CNC Drill Line is able to lay out and drill holes in any steel profile in half the time it takes with a mag drilling machine.

Cnc Beam Drill Line Increase

CNC Drill Lines are designed for general job shops and fabricators who need to drill holes into steel profiles of any type. Take a look at the following questions to determine if this machine suits your needs.

We always train your operator how to run the machine using Peddimat as you are often going to have the situation where a customer arrives with a couple of pieces of steel that need holes or layout marks and you want to be able to produce them quickly without bothering your detailing staff who might be busy on a larger job.

Quality

Check our other pages :

Which bar is used in beam

Auto Stand-Off – This is currently defined to be surface stand-off and not to be confused with vector stand-off in 5-axis mode. The current auto stand-off is based on a changing surface and will adjust vertically based on the angle of the “A” Axis, so there is five (5) axis taken into account during the calculations, but this is not the same as the tool vector stand-off. There is the ability to do the vector stand-off change while the machine is running manually with buttons on the screen.

Voortman-designed beam drilling lines have intelligence not only in their own capabilities but also in the fact that they can be plugged into any environment because of their modularity. Tandem solutions, such as band saws with robotic coppers or PeddiWriters, expand the shop’s throughput positioning. It allows for a more cost-effective approach when the steel sector cools down and a more aggressive one when it heats. Voortman invented the Multmaster, which can be used to advance small parts into a tandem-bandsaw. Fabricators are more profitable when they use the whole profile and minimize the remnant. Do you want more output? Check. Material handling is key to any Voortman CNC drill-line profit. Fabricators not only lose money when a profile is manually moved but material handling is far safer than using fork trucks and cranes to move the largest profiles.

Frequently Asked Questions

American Standard S-Beam, a type I-beam, is resistant to bending and shear loads. It is used in construction, shipbuilding, as well as other industries. An S-beam is similar to an I-beam but has tapered flanges which slope away from its inside surface.

The Beam L/D Ratio Diagnostic is used to display a plot of the length/diameter of all the beam elements in the model. The optimal L/D ratio to cool channel-related beam elements is 2.5. Solver convergence warnings may be issued if the L/D ratio is significantly lower.

C-Channel is usually stronger than tube in the vertical direction (as shown in the beam profile chart picture above).

The incident was prevented by a slip and cut program. Normal wear is not considered to have been a factor. Rowan's slip-and-cut program is used between 3,000 to 3,700 ton miles. It has a cut objective of one foot for every 35 ton miles.

The strength tolerances of the C-beam are lower than those of the I-beam. This results in lighter components. Continue reading if you have never used C-beam profiles.