


Tourism in Dubai is a major part of the economy of Dubai. Dubai was the third most visited city in the world in 2023 with 17 million international visitors according to Euromonitor International.[1][2] Dubai hosts more than 800 hotels with more than 150,000 rooms.[3][4]
The discovery of oil in 1966 kick-started the development of present Dubai, however Sheikh Hamad bin Maktoum (ruler from 1958 till 1990) realised one day Dubai would run out of oil and started building an economy that would outlast it.[5] A quote commonly attributed to Sheikh Rashid reflected his concern that Dubai's oil, which was discovered in 1966 and which began production in 1969, would run out within a few generations. Sheikh Rashid stated "My grandfather rode a camel, my father rode a camel, I drive a Mercedes, my son drives a Land Rover, his son will drive a Land Rover, but his son will ride a camel".[6] Sheikh Rashid realized early he needed to diversify the emirate of Dubai's economy by building on the city's trading history and therefore he set out to establish Dubai as the region's trade and service hub. By 1979, he was successful in establishing the Jebel Ali Port, which became the logical shipping centre for the entire United Arab Emirates and the world's largest man-made port. He also upgraded Dubai International Airport and built the Dubai World Trade Centre, which was then the tallest building in the Middle East. By the end of the 1970s, the stage was set for the diversification of Dubai's economy away from oil and into other areas such as tourism.[7]
In 1989 the Dubai Commerce and Tourism Promotion Board was established, to promote Dubai as a luxury destination for the up-tier market and influential business sectors. In January 1997, it was replaced with the Department of Tourism and Commerce Marketing (DTCM).[8]
In May 2013, the government of Dubai launched the Dubai Tourism Strategy 2020, with the key objective to attract 20 million visitors a year by 2020 and making Dubai a first choice destination for international leisure travellers as well as business travellers.[9] In 2018, the strategy was expanded by setting new goals of attracting 21-23 million visitors in 2022 and 23-25 million visitors by 2025.[10] The key objectives from 2013 and 2018 were not met due to the COVID-19 pandemic.
The need to maintain its tourism industry has hampered Dubai's response to the COVID-19 pandemic.[11] Along with COVID-19 Dubai's tourism sector has also been hurt by a greater international awareness of the status of human rights in the emirate and in particular the treatment of Princess Latifa bint Mohammed Al Maktoum.[12]
In November 2022, Sheikh Mohammed bin Rashid announced a national tourism strategy until 2031. The goal of the strategy is to attract Dh 100 billion in additional tourism investments (so that the tourism sector's contribution will be Dh450bn of Dubai's GDP in 2031) and receive 40 million hotel guests in 2031. The strategy includes 25 initiatives and policies to support the development of the tourism sector in the country.[13]
In April 2025, the Dubai Department of Economy and Tourism introduced a new programme offering media training to students for promotion of tourism in the UAE. Applicants are provided with flights, luxury apartment and three months of income, along with certification from Dubai College of Tourism for posting about traveling experiences in Dubai on social media. According to Middle East Eye, this program aims to whitewash its human rights violations and war crime accusations in Sudan.[14]
Since 1982, Dubai continued to be one of the fastest growing destinations for tourists. In 2002, visitors were mainly from other Gulf Cooperation Council members which accounted for 34% of tourists, South Asia accounted for 25%, other Arab states 16%, Europe 15%, and Africa 9%. In 2003, revenue from tourism exceeded $1 billion and surpassed oil revenues to directly and indirectly account for over 17% and 28% of GDP respectively.[15]
From January to June 2019 8.36 million international tourists visited Dubai. Most of the visitors were from India (997,000) followed by Saudi Arabia (755,000) and the United Kingdom (586,000).[16]
Mastercard's Global Destination Cities Index 2019 found that tourists spend more in Dubai than in any other country. In 2018, the country topped the list for the fourth year in a row with a total spend of $30.82 billion, a 3.8% increase over 2017 ($29.70 billion). The average spend per day was $553.[17]
In 2019, Dubai attracted a total of 16.73 million tourists, which was an increase of 5.09% on the previous year. However, in 2020, the number of visitors dropped to 5.51 million due to the coronavirus pandemic.[18]
| Year | Total international visitors [19][20][21][15][22][23] |
Increase/decrease | Visitor spending ($m)[24] |
|---|---|---|---|
| 1982 | 374,400 | N/a | |
| 1990 | 632,903 | ||
| 1991 | 716,642 | ||
| 1992 | 944,350 | ||
| 1993 | 1,088,000 | ||
| 1994 | 1,239,000 | ||
| 1995 | 1,601,000 | 632.0 | |
| 1996 | 1,768,000 | 743.0 | |
| 1997 | 1,792,000 | 814.0 | |
| 1998 | 2,184,000 | 859.0 | |
| 1999 | 2,481,000 | 893.0 | |
| 2000 | 3,027,000 | 1,063.0 | |
| 2001 | 3,626,625 | 1,200.0 | |
| 2002 | 4,756,280 | 1,332.0 | |
| 2003 | 4,980,228 | 1,438.0 | |
| 2004 | 5,420,000 | 1,593.0 | |
| 2005 | 6,160,003 | 3,218.0 | |
| 2006 | 6,441,670 | 4,972.0 | |
| 2007 | 6,951,798[25][26] | 6,072.0 | |
| 2008 | 6,996,449[25] | 7,162.0 | |
| 2009 | 7,580,000[27] | 7,352.0 | |
| 2010 | 8,410,000 | 8,577.0 | |
| 2011 | 9,910,000 | 9,204.0 | |
| 2012 | 10,950,000 | 10,924.0 | |
| 2013 | 12,900,000 | 12,389.0 | |
| 2014 | 13,200,000 | 15,221.0 | |
| 2015 | 14,200,000 | 25,587.1 | |
| 2016 | 14,870,000 | 28,657.4 | |
| 2017 | 15,790,000 | 29,705.5 | |
| 2018 | 15,920,000 | 34,609.5 | |
| 2019 | 16,730,000 | 38,413.3 | |
| 2020 | 5,510,000[a] | 24,615.4 | |
| 2021 | 7,280,000[b] | ||
| 2022 | 14,360,000[28] | ||
| 2023 | 17,150,000[29] | ||
| 2024 | 18,720,000[30] |
In the last three years, Dubai saw an increase in 4 and 5 star hotels and number of rooms, but a decrease in standard hotel apartments. The total number of rooms increased by 9,098 from 2015 to 2017, an increase of 9.25%. Prior to the Expo 2020 hotels in Dubai were reducing room rates to stimulate demand as supply accelerated. Based on data of August 2019, Dubai hoteliers reported a 7.6% rise in supply against 7.4% increase in demand.[31] Average room rates stood at AED 486 in June 2019 while in the same month of 2018 average room rates were at 544 AED.[32] In July 2019, Dubai's Jumeirah Group LLC fired 500 people due to a decline in tourism. In the second quarter of 2019, hospitality sector has had the worst quarter since 2009.[33]
| 2014 | 2015 | 2016 | 2017 | 2018 | 2019 | 2020 | 2021 | 2022 | 2023 | |
|---|---|---|---|---|---|---|---|---|---|---|
| Total 5 star hotels | 91 | 96 | 103 | 113 | 128 | 134 | 143 | 151 | 157 | |
| Total 5 star hotel rooms | 31,551 | 33,122 | 35,853 | 38,543 | 43,133 | 44,067 | 47,035 | 49,585 | 51,809 | |
| Total 4 star hotels | 106 | 112 | 122 | 146 | 158 | 161 | 181 | 189 | 194 | |
| Total 4 star hotel rooms | 21,208 | 22,990 | 25,289 | 29,908 | 33,120 | 34,905 | 40,377 | 42,505 | 43,283 | |
| Total 1-3 star hotels | 264 | 267 | 260 | 260 | 258 | 225 | 243 | 270 | 274 | |
| Total 1-3 star hotel rooms | 19,714 | 21,767 | 21,591 | 22,634 | 24,491 | 21,732 | 25,384 | 28,512 | 28,789 | |
| Total hotel apartments (deluxe/superior) | 66 | 66 | 65 | 68 | 68 | 74 | 80 | 82 | 85 | |
| Total deluxe/superior rooms | 9,641 | 9,519 | 9,786 | 10,522 | 10,520 | 11,845 | 12,606 | 13,113 | 13,842 | |
| Total hotel apartments (standard) | 150 | 140 | 131 | 129 | 129 | 117 | 108 | 112 | 111 | |
| Total standard rooms | 16,219 | 15,447 | 14,930 | 14,360 | 14,856 | 14,398 | 12,548 | 12,781 | 12,568 | |
| Total establishments | 657 | 677 | 681 | 681 | 716 | 741 | 711 | 755 | 804 | 821 |
| Total available rooms | 92,333 | 98,333 | 102,845 | 107,431 | 115,967 | 126,120 | 126,947 | 137,950 | 146,496 | 150,291 |
| Average occupancy | 79% | 77% | 78% | 78% | 76% | 75% | 54% | 67% | 73% | 77% |
|
|
This section does not cite any sources. (August 2024)
|
| Rank | Country | 6/2023 | 2022 |
|---|---|---|---|
| 1 | 1,223,000 | 1,842,000 | |
| 5 | 616,000 | 758,000 | |
| 4 | 555,000 | 1,043,000 | |
| 3 | 538,000 | 1,216,000 | |
| 2 | 511,000 | 1,311,000 | |
| 6 | 362,000 | 590,000 | |
| 7 | 329,000 | 422,000 | |
| 17 | 260,000 | 177,000 | |
| 10 | 196,000 | 328,000 | |
| 13 | 196,000 | 239,000 | |
| 8 | 180,000 | 364,000 | |
| 11 | 168,000 | 288,000 | |
| 12 | 152,000 | 260,000 | |
| 9 | 152,000 | 356,000 | |
| 14 | 145,000 | 234,000 | |
| 15 | 130,000 | 212,000 | |
| 19 | 125,000 | 158,000 | |
| 16 | 121,000 | 184,000 | |
| 18 | 110,000 | 158,000 | |
| 19 | 110,000 | 148,000 |
|
|
This section needs additional citations for verification. (September 2021)
|
Aspects of Dubai's old culture, while occasionally overshadowed by the boom in economic development, can be found by visiting places around the creek, which splits Dubai into two halves, Bur Dubai and Deira. The buildings lining the Bur Dubai side of the Creek provide the main flavor of the old city. Heritage Village is one of the few remaining parts of historical Dubai, containing preserved buildings. The adjoining Diving Village offers exhibits on pearl diving and fishing. The Diving Village forms part of an ambitious plan to turn the entire "Shindagha" area into a cultural city, recreating life in Dubai as it was in days gone by.
Other attractions include the Sheikh Saeed Al Maktoum House; the Dubai Museum in the restored Al Fahidi Fort, which was erected around 1799; and the Heritage Village of Hatta, situated 115 kilometers southeast of Dubai City in the heart of the rocky Hatta Mountains. The history of the village can be traced back 2000 – 3000 years. It consists of 30 buildings, each differing in size, interior layout and building materials used. Great care was taken to use the same materials as those used when originally built during the renovation such as mud, hay, sandalwood and palm fronds. The Sharia Mosque is an old mosque built in the early 19th century using the same building materials and consists of a large prayer hall, a court and courtyard, minaret and other utility rooms.[34] Other museums include the Al Ahmadiya School.
Dubai has been nicknamed the "shopping capital of the Middle East."[35][36] The city draws large numbers of shopping tourists from countries within the region and from as far as Eastern Europe, Africa and the Indian Subcontinent. Dubai is known for its souk districts. Souk is the Arabic word for market or place where any kind of goods are brought or exchanged. Traditionally, dhows from the Far East, China, Sri Lanka, and India would discharge their cargo and the goods would be bargained over in the souks adjacent to the docks.[37]
Modern shopping malls and boutiques are also found in the city. Dubai Duty Free at Dubai International Airport offers merchandise catering to the multinational passengers using Dubai International Airport. Outside of Duty Free areas and major sales, Dubai has a reputation for being one of the most expensive shopping destinations in the world.[38]
While boutiques, some electronics shops, department stores and supermarkets may operate on a fixed-price basis, most other outlets consider friendly negotiation as a way of life.
Dubai's numerous shopping centres cater for every consumer's need. Cars, clothing, jewellery, electronics, furnishing, sporting equipment and any other goods will all be likely to be under the same roof.[39]
The Dubai Shopping Festival is a month-long festival held during the month of January each year. During the festival the entire emirate becomes one massive shopping mall. Additionally, the festival brings together music shows, art exhibitions, and folk dances.[40]
The Dubai Summer Surprises (DSS) is the summer version of Dubai Shopping Festival held during June, July and August. Dubai Government launched Dubai Summer Surprises in 1998 in order to promote Dubai as a family holiday destination. DSS offers fun, entertainment, food deals and great offers on shopping.
Tourists are required to obey some Muslim religious restrictions in public even if they are not Muslim themselves, such as refraining from eating or drinking in public places in the daytime during Ramadan.[41]
Dubai has a modest dress code as part of its criminal law.[42] Sleeveless tops and short dresses are not encouraged at Dubai Mall.[43][44] Clothes are advised to be in appropriate lengths.[42]
Homosexuality is criminalized in Dubai, including for tourists. However, there is a vibrant underground gay scene in Dubai and authorities do not actively search for homosexuals to enforce the law.[45]
Most capitals and other major cities have direct flights to Dubai. More than 120 airlines operate to and from Dubai International Airport to more than 260 destinations. Dubai International Airport is the world's busiest airport by international passenger traffic.[46] Dubai is also the home base of the airline Emirates, which operates scheduled services to more than 100 destinations.
In June 2009 Emirates designated a special handling area at departures and arrivals for passengers with special needs, allowing wheelchair passengers to receive a more personalized service.[47][better source needed]
The establishment of the first cruise terminal in Dubai in 2001 and the opening of the enhanced New Dubai Cruise Terminal in February 2010 with higher handling capacity has drawn the attention of cruise line operators. Cruises to Dubai sail from: Singapore, Sydney, Athens, Dover, Venice, Cape Town, Civitavecchia, Piraeus, Alexandria, Istanbul, New York City, Southampton, Barcelona, Fort Lauderdale, Miami, Los Angeles, Mumbai, Hong Kong, Shanghai, Monte Carlo, Mombasa, Victoria, and Cairns among others.[48][better source needed]
The United Arab Emirates has a network of roads that connect major towns and villages, including a multi-lane highway between Dubai and Abu Dhabi, with access to and from the bordering countries of Saudi Arabia and Oman. Highways and main roads in Dubai and the United Arab Emirates are designated by an Emirate Route Number. Speed limits are displayed on road signs and are usually 60–80 km/h (37–50 mph) around town and 100–120 km/h (62–75 mph) elsewhere.[49][better source needed]
Dubai ranked third in the best taxi services behind Tokyo and Singapore.[50][better source needed]
Travelers entering Dubai are warned for harsh penalties regarding illicit drug use or smuggling. Authorities in Dubai use highly sensitive equipment to conduct thorough searches to find trace amount of illegal substances.[51] A senior Dubai judge was quoted on February 11, 2008, by the Dubai City News saying, "These laws help discourage anyone from carrying or using drugs. Even if the quantity of illegal drugs found on someone is 0.05 grams, they will be found guilty. The penalty is a minimum of four years. The message is clear — drugs will not be tolerated."[51]
No special immunizations are required, but tourists are encouraged to purchase appropriate medical insurance before travelling. Government immunization programs have led to recognition by a travel magazine.[47] As a latest addition to the established modern health care system, Dubai offers online health care contacts of virtually all medical doctors in Dubai.[52]
|
|
This section does not cite any sources. (September 2021)
|
Dubai hosts the following international championships:
A hot air balloon is a lighter-than-air aircraft consisting of a bag, called an envelope, which contains heated air. Suspended beneath is a gondola or wicker basket (in some long-distance or high-altitude balloons, a capsule), which carries passengers and a source of heat, in most cases an open flame caused by burning liquid propane. The heated air inside the envelope makes it buoyant, since it has a lower density than the colder air outside the envelope. As with all aircraft, hot air balloons cannot fly beyond the atmosphere. The envelope does not have to be sealed at the bottom, since the air inside the envelope is at about the same pressure as the surrounding air. In modern sport balloons the envelope is generally made from nylon fabric, and the inlet of the balloon (closest to the burner flame) is made from a fire-resistant material such as Nomex. Modern balloons have been made in many shapes, such as rocket ships and the shapes of various commercial products, though the traditional shape is used for most non-commercial and many commercial applications.
The hot air balloon is the first successful human-carrying flight technology. The first untethered manned hot air balloon flight in the world was performed in Paris, France, by Jean-François Pilâtre de Rozier and François Laurent d'Arlandes on November 21, 1783,[1] in a balloon created by the Montgolfier brothers.[2] Hot air balloons that can be propelled through the air rather than simply drifting with the wind are known as thermal airships.
A precursor of the hot air balloon was the sky lantern (simplified Chinese: 孔明灯; traditional Chinese: 孔明燈). Zhuge Liang of the Shu Han kingdom, during the Three Kingdoms era (220–280 CE), used these airborne lanterns for military signaling.[3] The Mongolian army studied Kongming lanterns from China and used them in the Battle of Legnica during the Mongol invasion of Poland in the 13th century.[4] This is the first time ballooning was known in the western world.
In the 18th century the Portuguese Jesuit priest Bartolomeu de Gusmão in colonial Brazil envisioned an aerial apparatus named Passarola, which was the predecessor of the hot air balloon. The Passarola was intended to serve as an air vessel in order to facilitate communication and as a strategical device.[5] In 1709 John V of Portugal decided to fund Bartolomeu de Gusmão's project following a petition made by the Jesuit priest,[6] and an unmanned demonstration was performed at Casa da Índia in the presence of John V and the queen, Maria Anna of Austria, with the Italian cardinal Michelangelo Conti, two members of the Portuguese Royal Academy of History, one Portuguese diplomat and one chronicler serving as witnesses. This event would bring some European attention to this event and this project. A later article dated on October 20, 1786, by the London Daily Universal Register would state that the inventor was able to raise himself by the use of his prototype. Also in 1709, the Portuguese Jesuit wrote Manifesto summário para os que ignoram poderse navegar pelo elemento do ar (Short Manifesto for those who are unaware that is possible to sail through the element air); he also left designs for a manned air vessel.
In the 1970s, balloonist Julian Nott hypothesized that the Nazca Lines geoglyphs' creation two millennia ago could have been guided by Nazca leaders in a balloon, possibly the earliest hot air balloon flights in human history.[7] To support this theory, in 1975 he designed and piloted the Nazca Prehistoric Balloon, claiming to have used only methods and materials available to the Pre-Inca Peruvians 1,000 years ago.[8][9]
The French brothers Joseph-Michel and Jacques-Étienne Montgolfier developed a hot-air balloon in Annonay, Ardèche, France, and demonstrated it publicly on September 19, 1783, making an unmanned flight lasting 10 minutes. After experimenting with unmanned balloons and flights with animals, the first balloon flight with humans aboard, a tethered flight, performed on or around October 15, 1783, by Jean-Francois Pilatre de Rozier, who made at least one tethered flight from the yard of the Reveillon workshop in the Faubourg Saint-Antoine. Later that same day, Pilatre de Rozier became the second human to ascend into the air, reaching an altitude of 26 m (85 ft), the length of the tether.[10][11] The first free flight with human passengers was made a few weeks later, on November 21, 1783.[2] King Louis XVI had originally decreed that condemned criminals would be the first pilots, but de Rozier, along with Marquis François d'Arlandes, petitioned successfully for the honor.[12][13][14] The first military use of a hot air balloon happened in 1794 during the battle of Fleurus, when the French used the balloon l'Entreprenant for observation.[15]
Modern hot air balloons, with an onboard heat source, were developed by Ed Yost and Jim Winker, beginning during the 1950s; their work resulted in his a first successful flight on October 22, 1960.[16] The first modern hot air balloon to be made in the United Kingdom (UK) was the Bristol Belle, built in 1967. Presently, hot air balloons are used primarily for recreation.
On November 26, 2005 Vijaypat Singhania set the world altitude record for highest hot air balloon flight, reaching 21,027 m (68,986 ft). He took off from downtown Mumbai, India, and landed 240 km (150 mi) south in Panchale.[17]
The previous record of 19,811 m (64,997 ft) had been set by Per Lindstrand on June 6, 1988, in Plano, Texas.
On January 15, 1991, Per Lindstrand (born in Sweden, but resident in the UK) and Richard Branson of the UK flew 7,671.91 km (4,767.10 mi) from Japan to Northern Canada in the “Virgin Pacific Flyer”. With a volume of 74,000 cubic meters (2.6 million cubic feet), the balloon envelope was the largest ever built for a hot air craft. Designed to fly in the trans-oceanic jet streams, the Pacific Flyer recorded the fastest ground speed for a manned balloon at 394 km/h (245 mph).
The longest duration record was set by Swiss psychiatrist Bertrand Piccard (Auguste Piccard's grandson) and Briton Brian Jones, flying in the Breitling Orbiter 3. It was the first nonstop trip around the world by balloon. The balloon left Château-d'Oex, Switzerland, on March 1, 1999, and landed at 1:02 a.m. on March 21 in the Egyptian desert 500 km (300 mi) south of Cairo. The two men exceeded distance, endurance, and time records, traveling 19 days, 21 hours, and 55 minutes.
Steve Fossett, flying solo, exceeded the record for briefest time traveling around the world on 3 July 2002 on his sixth attempt,[18] in 320 h 33 min.[19] Fedor Konyukhov flew solo round the world on his first attempt in a hybrid hot air/helium balloon from 11 to 23 July 2016[20] for a round-the world time of 268 h 20 min.[19]
A hot air balloon for manned flight uses a single-layered, fabric gas bag (lifting "envelope"), with an opening at the bottom called the mouth or throat. Attached to the envelope is a basket, or gondola, for carrying the passengers. Mounted above the basket and centered in the mouth is the "burner", which injects a flame into the envelope, heating the air within. The heater or burner is fueled by propane, a liquefied gas stored in pressure vessels, similar to high-pressure forklift cylinders.[21][22]
Modern hot air balloons are usually made of materials such as ripstop nylon or dacron (a polyester).[23]
During the manufacturing process, the material is cut into panels and sewn together, along with structural load tapes that carry the weight of the gondola or basket. The individual sections, which extend from the throat to the crown (top) of the envelope, are known as gores or gore sections. Envelopes can have as few as 4 gores or as many as 24 or more.[24]
Envelopes often have a crown ring at their very top. This is a hoop of smooth metal, usually aluminium, and approximately 30 cm (1 ft) in diameter. Vertical load tapes from the envelope are attached to the crown ring.
At the bottom of the envelope the vertical load tapes are sewn into loops that are connected to cables (one cable per load tape). These cables, often referred to as flying wires, are connected to the basket by carabiners.
The most common technique for sewing panels together is called the French felled, French fell, or double lap seam.[25][26][27][28] The two pieces of fabric are folded over on each other at their common edge, possibly with a load tape as well, and sewn together with two rows of parallel stitching. Other methods include a flat lap seam, in which the two pieces of fabric are held together simply with two rows of parallel stitching, and a zigzag, where parallel zigzag stitching holds a double lap of fabric.[27]
The fabric (or at least part of it, the top 1/3, for example) may be coated with a sealer, such as silicone or polyurethane, to make it impermeable to air.[29] It is often the degradation of this coating and the corresponding loss of impermeability that ends the effective life of an envelope, not weakening of the fabric itself. Heat, moisture, and mechanical wear-and-tear during set-up and pack-up are the primary causes of degradation. Once an envelope becomes too porous to fly, it may be retired and discarded or perhaps used as a "rag bag": cold-inflated and opened for children to run through. Products for recoating the fabric are becoming available commercially.[30]
A range of envelope sizes is available. The smallest, one-person, basket-less balloons (called "Hoppers" or "Cloudhoppers") have as little as 600 m3 (21,000 cu ft) of envelope volume;[31] for a perfect sphere the radius would be around 5 m (16 ft). At the other end of the scale, balloons used by commercial sightseeing operations may be able to carry well over two dozen people, with envelope volumes of up to 17,000 m3 (600,000 cu ft).[31] The most-used size is about 2,800 m3 (99,000 cu ft), allowing to carry 3 to 5 people.
The top of the balloon usually has a vent of some sort, enabling the pilot to release hot air to slow an ascent, start a descent, or increase the rate of descent, usually for landing. Some hot air balloons have turning vents, which are side vents that, when opened, cause the balloon to rotate. Such vents are particularly useful for balloons with rectangular baskets, to facilitate aligning the wider side of the basket for landing.[32]
The most common type of top vent is a disk-shaped flap of fabric called a parachute vent, invented by Tracy Barnes.[33] The fabric is connected around its edge to a set of "vent lines" that converge in the center. (The arrangement of fabric and lines roughly resembles a parachute—thus the name.) These "vent lines" are themselves connected to a control line that runs to the basket. A parachute vent is opened by pulling on the control line. Once the control line is released, the pressure of the remaining hot air pushes the vent fabric back into place. A parachute vent can be opened briefly while in flight to initiate a rapid descent. (Slower descents are initiated by allowing the air in the balloon to cool naturally.) The vent is pulled open completely to collapse the balloon after landing.
An older, and presently less commonly used, style of top vent is called a "Velcro-style" vent. This too is a disk of fabric at the top of the balloon. However, rather than having a set of "vent lines" that can repeatedly open and close the vent, the vent is secured by "hook and loop" fasteners (such as Velcro) and is only opened at the end of the flight. Balloons equipped with a Velcro-style vent typically have a second "maneuvering vent" built into the side (as opposed to the top) of the balloon. Another common type of top design is the "smart vent", which, rather than lowering a fabric disc into the envelope as in the "parachute" type, gathers the fabric together in the center of the opening. This system can theoretically be used for in-flight maneuvering, but is more commonly used only as a rapid-deflation device for use after landing, of particular value in high winds. Other designs, such as the "pop top" and "MultiVent" systems, have also attempted to address the need for rapid deflation on landing, but the parachute top remains popular as an all-around maneuvering and deflation system.
Besides special shapes, possibly for marketing purposes, there are several variations on the traditional "inverted tear drop" shape. The simplest, often used by home builders, is a hemisphere on top of a truncated cone. More sophisticated designs attempt to minimize the circumferential stress on the fabric, with different degrees of success depending on whether they take fabric weight and varying air density into account. This shape may be referred to as "natural".[34] Finally, some specialized balloons are designed to minimize aerodynamic drag (in the vertical direction) to improve flight performance in competitions.[35]
Hot air balloon baskets are commonly made of woven wicker or rattan. These materials have proven to be sufficiently light, strong, and durable for balloon flight. Such baskets are usually rectangular or triangular in shape. They vary in size from just big enough for two people to large enough to carry thirty.[36] Larger baskets often have internal partitions for structural bracing and to compartmentalize the passengers. Small holes may be woven into the side of the basket to act as foot holds for passengers climbing in or out.[37]
Baskets may also be made of aluminium, especially a collapsible aluminium frame with a fabric skin, to reduce weight or increase portability.[38] These may be used by pilots without a ground crew or who are attempting to set altitude, duration, or distance records. Other specialty baskets include the fully enclosed gondolas used for around-the-world attempts[39] and baskets that consist of little more than a seat for the pilot and perhaps one passenger.
The burner unit gasifies liquid propane,[40] mixes it with air, ignites the mixture, and directs the flame and exhaust into the mouth of the envelope. Burners vary in power output; each will generally produce 2 to 3 MW of heat (7 to 10 million BTUs per hour), with double, triple, or quadruple burner configurations installed where more power is needed.[41][42] The pilot actuates a burner by opening a propane valve, known as a blast valve. The valve may be spring-loaded, so that it closes automatically, or it may stay open until closed by the pilot. The burner has a pilot light to ignite the propane and air mixture. The pilot light may be lit by the pilot with an external device, such as a flint striker or a lighter, or with a built-in piezoelectric spark.[43]
Where more than one burner is present, the pilot can use one or more at a time, depending on the desired heat output. Each burner has a metal coil of propane tubing the flame shoots through to preheat the incoming liquid propane. The burner unit may be suspended from the mouth of the envelope or supported rigidly over the basket. The burner unit may be mounted on a gimbal to enable the pilot to aim the flame and avoid overheating the envelope fabric. A burner may have a secondary propane valve that releases propane more slowly and thereby generates a different sound. This is called a whisper burner and is used for flight over livestock to lessen the chance of spooking them. It also generates a more yellow flame and is used for night glows because it lights up the inside of the envelope better than the primary valve.
Propane fuel tanks are usually cylindrical pressure vessels made from aluminium, stainless steel, or titanium with a valve at one end to feed the burner and to refuel. They may have a fuel gauge and a pressure gauge. Common tank sizes are 38, 57 and 76 litres (10, 15 and 20 US gallons).[29] They may be intended for upright or horizontal use and may be mounted inside or outside the basket.
The pressure necessary to force the fuel through the line to the burner may be supplied by the vapor pressure of the propane itself, if warm enough, or by the introduction of an inert gas such as nitrogen.[43] Tanks may be preheated with electrical heat tapes to produce sufficient vapor pressure for cold-weather flying.[44] Warmed tanks are usually also wrapped in an insulating blanket to preserve heat during the setup and flight.
A balloon may be outfitted with a variety of instruments to aid the pilot. These commonly include an altimeter, a rate-of-climb (vertical-speed) indicator known as a variometer, envelope (air) temperature, and ambient (air) temperature.[45] A GPS receiver can be useful to indicate ground speed (traditional aircraft air-speed indicators would be useless) and direction.
The combined mass of an average system can be calculated as follows:[29]
| Component | Pounds | Kilograms | Mass fraction |
|---|---|---|---|
| 2,800 m3 (100,000 cu ft) envelope | 250 | 113.4 | |
| 5-passenger basket | 140 | 63.5 | |
| Double burner | 50 | 22.7 | |
| 3 76 L (20 US gal) fuel tanks full of propane | 3 × 135 = 405 | 183.7 | |
| 5 passengers | 5 × 150 = 750 | 340.2 | |
| Subtotal | 1595 | 723.5 | |
| 2,800 m3 (100,000 cu ft) of heated air* | 5922 | 2686.2 | |
| Total | (3.76 tons) 7517 | 3409.7 |
Increasing the air temperature inside the envelope makes it less dense than the surrounding (ambient) air. The balloon floats because of the buoyant force exerted on it. This force is the same force that acts on objects when they are in water and is described by Archimedes' principle. The amount of lift (or buoyancy) provided by a hot air balloon depends primarily upon the difference between the temperature of the air inside the envelope and the temperature of the air outside the envelope. For most envelopes made of nylon fabric, the maximal internal temperature is limited to approximately 120 °C (250 °F).[46]
The melting point of nylon is significantly greater than this maximal operating temperature—about 230 °C (450 °F)—but higher temperatures cause the strength of the nylon fabric to degrade more quickly over time. With a maximal operating temperature of 120 °C (250 °F), balloon envelopes can generally be flown for between 400 and 500 hours before the fabric needs to be replaced. Many balloon pilots operate their envelopes at temperatures significantly less than the maximum to extend envelope-fabric life.
The lift generated by 2,800 m3 (100,000 cu ft) of dry air heated to various temperatures may be calculated as follows:
| Air temperature °C (°F) |
Air density kg/m3 (lb/cu ft) |
Air mass kg (lb) |
Lift generated kg (lb) |
|---|---|---|---|
| 20 (68) | 1.2041 (0.07517) | 3,409.7 (7,517) | 0, (0) |
| 99 (210) | 0.9486 (0.05922) | 2,686.2 (5,922) | 723.5 (1,595) |
| 120 (248) | 0.8978 (0.05605) | 2,542.4 (5,605) | 867.3 (1,912) |
The density of air at 20 °C (68 °F) is about 1.2 kg/m3 (0.075 lb/cu ft). The total lift for a balloon of 2,800 m3 (100,000 cu ft) heated to 99 °C (210 °F) would be 723.5 kg (1,595 lb). This is just enough to generate neutral buoyancy for the total system mass (not including the heated air trapped in the envelope, of course) stated in the previous section. Liftoff would require a slightly greater temperature, depending on the desired rate of climb. In reality, the air contained in the envelope is not all at the same temperature, as the accompanying thermal image shows, and so these calculations are based on averages.
For typical atmospheric conditions (20 °C or 68 °F), a hot air balloon heated to 99 °C (210 °F) requires about 3.91 m3 of envelope volume to lift 1 kilogram (equivalently, 62.5 cu ft/lb). The precise amount of lift provided depends not only upon the internal temperature mentioned above, but the external temperature, altitude above sea level, and humidity of the air surrounding. On a warm day, a balloon cannot lift as much as on a cool day, because the temperature required for launch will exceed the maximum sustainable for nylon envelope fabric. Also, in the lower atmosphere, the lift provided by a hot air balloon decreases about 3% per 1,000 m (1% per 1,000 ft) of altitude gained.[47]
There are several different types of hot air balloons, all with different means of taking and sustaining flight.
Standard hot air balloons are known as Montgolfier balloons and rely solely on the buoyancy of hot air provided by the burner and contained by the envelope.[48] This style of balloon was developed by the Montgolfier brothers and had its first public demonstration on 4 June 1783 with an unmanned flight lasting 10 minutes, followed later that year with manned flights.[49]
Instead of using regular air it is also possible to use lighter than air gasses such as Helium or Hydrogen to lift the balloon,[51] though this means it is technically not a hot air balloon, though they did influence the design of hybrid balloons.
The 1785 Rozière balloon, is the main type of hybrid balloon, named after its creator, Jean-François Pilâtre de Rozier. It has a separate cell for a lighter-than-air gas (typically helium), as well as a cone below for hot air (as is used in a hot air balloon) to heat the helium at night. Hydrogen gas was used in the very early stages of development but was quickly abandoned due to the danger of introducing an open flame near the gas, for example when Rozier attempted to cross the English Channel with his prototype, the fire used to heat the air ignited the Hydrogen and killed both him and his copilot thirty minutes after takeoff.[52] As such, all modern hybrid balloons now use helium as a lifting gas.[53] These balloons are commonly used for high performance records for hot air balloons.
Solar balloons are hot air balloons that use just solar energy captured by an envelope. These envelopes are more specialized than for other hot air balloons, trying to maximize the amount of solar energy they collect. This can be accomplished by rotating the envelope during flight or by having the envelope colored black or another dark color.[54] They were pioneered in the 1970s in Europe by Tracy Barnes, Dominic Michaelis, and in the US by Frederick Espoo and Paul Woessher.[55]
A Thermal airship, or blimp, became a reality in the 1960s. Thermal airships were the first steerable air buoyant vehicles.[56] They utilized tail fins and a rudder and contained strictly hot air rather than a mix with hydrogen or helium.[56]
Observation balloons were deployed as early as the American Civil War and used as reconnaissance towers.[57] The first military funded balloon in America was designed by Thaddeus Lowe on August 2, 1861, for the Union.[57] His design utilized gas from municipal lines to inflate the balloon as he did not have access to a portable generator.[57] Observation balloons during this time were all made using multicolored-silk, wicker baskets, and were vertically oriented and tear shaped.[58] Hydrogen, or illumination gas became the most used inflation fuel by the 20th Century, as it was lighter than air.[58] Observation balloon usage skyrocketed in Britain by the Royal Engineers at the end of the 19th Century, deploying to Sudan in 1885 and to South Africa during the Second Boer War from 1899 to 1902.[59]
Due to the overall design of hot air balloons, controlled and precise steering of hot air balloons is not possible; it is possible for pilots to try to achieve basic directional control by changing altitude and catching different wind streams.[60] Wind in the northern hemisphere tends to turn east due to coriolis effect as the altitude increases.
The most effective way of landing a hot air balloon is to reduce the energy in the envelope, either by turning down the flame in Montgolfier and Hybrid balloons, or more directly by opening a flap in the envelope that will release the air/gas inside.[60]
|
|
This section does not cite any sources. (August 2009)
|
To help ensure the safety of pilot and passengers, a hot air balloon may carry several pieces of safety equipment.
To relight the burner if the pilot light goes out and the optional piezo ignition fails, the pilot should have ready access to a means of backup ignition, such as a flint spark lighter. Many systems, especially those that carry passengers, have completely duplicate fuel and burner systems: two fuel tanks, connected to two separate hoses, which feed two distinct burners. This enables a safe landing in the case of a blockage somewhere in one system or if a system must be disabled because of a fuel leak.
A fire extinguisher suitable for extinguishing propane fires is useful. Most balloons carry a 1 or 2 kg AB:E type fire extinguisher.[61]
A handling or drop line is mandatory safety equipment in many countries. This is a rope or webbing of 20–30 meters in length attached to the balloon basket with a quick-release connection at one end. In very calm winds the balloon pilot can throw the handling line from the balloon so that the ground crew can guide the balloon safely away from obstructions on the ground.[62]
For commercial passenger balloons, a pilot restraint harness is mandatory in some countries. This consists of a hip belt and a webbing line that together allow for some movement while preventing the pilot from being ejected from the basket during a hard landing.
Further safety equipment may include a first-aid kit, a fire blanket and a strong rescue knife.
At a minimum, the pilot should wear leather or flame-retardant fiber (such as nomex) gloves, so that they may shut off a gas valve in the case of a leak, even if there is a flame present; quick action in this regard can turn a potential catastrophe into a mere inconvenience. The pilot should additionally wear flame-resistant clothing covering their arms and legs; either natural fiber, such as cotton, linen, hemp, or wool, or engineered flame-retardant fiber, such as nomex, is acceptable in this capacity. Most engineered fibers (with the exception of rayon, which is also safe to wear) are thermoplastic; many are also hydrocarbons. This makes such fabrics very much unsuitable to wear near high temperatures, since non-flame-retardant thermoplastics will melt onto the wearer, and most hydrocarbons, whether fibrous or not, are suitable to use as fuels. Natural fiber will singe rather than melt or burn readily, and flame-retardant fiber generally has a very high melting point and is intrinsically non-flammable. Many pilots also advise their passengers to wear similar protective clothing that covers their arms and legs, as well as strong shoes or boots that offer good ankle support. Finally, some balloon systems, especially those that hang the burner from the envelope instead of supporting it rigidly from the basket, require the use of helmets by the pilot and passengers.
The ground crew should wear gloves whenever there is a possibility of handling ropes or lines. The mass and exposed surface to air movement of a medium-sized balloon is sufficient to cause rope friction burns to the hands of anyone trying to stop or prevent movement. The ground crew should also wear sturdy shoes and at least long pants in case of the need to access a landing or landed balloon in rough or overgrown terrain.
As with aircraft, hot air balloons require regular maintenance to remain airworthy. As aircraft made of fabric and that lack direct horizontal control, hot air balloons may occasionally require repairs to rips or snags. While some operations, such as cleaning and drying, may be performed by the owner or pilot, other operations, such as sewing, must be performed by a qualified repair technician and recorded in the balloon's maintenance log book.
To ensure long life and safe operation, the envelope should be kept clean and dry. This prevents mold and mildew from forming on the fabric and abrasion from occurring during packing, transport, and unpacking due to contact with foreign particles. In the event of a landing in a wet (because of precipitation or early morning or late evening dew) or muddy location (farmer's field), the envelope should be cleaned and laid out or hung to dry.
The burner and fuel system must also be kept clean to ensure safe operation on demand. Damaged fuel hoses need to be replaced. Stuck or leaky valves must be repaired or replaced. The wicker basket may require occasional refinishing or repair. The skids on its bottom may require occasional replacement.
Balloons in most parts of the world are maintained in accordance with a fixed manufacturer's maintenance schedule that includes regular (100 flight hours or 12 month) inspections, in addition to maintenance work to correct any damage. In Australia, balloons used for carrying commercial passengers must be inspected and maintained by approved workshops.[63]
In the case of a snag, burn, or rip in the envelope fabric, a patch may be applied or the affected panel completely replaced. Patches may be held in place with glue, tape, stitching, or a combination of these techniques. Replacing an entire panel requires the stitching around the old panel to be removed, and a new panel to be sewn in with the appropriate technique, thread, and stitch pattern.
Depending on the size of the balloon, location, and intended use, hot air balloons and their pilots need to comply with a variety of regulations.
As with other aircraft in the US, balloons must be registered (have an N-number), have an airworthiness certificate, and pass annual inspections. Balloons below a certain size (empty weight of less than 155 pounds or 70 kg including envelope, basket, burners and empty fuel tanks) can be used as an ultralight aircraft.
In Australia, private balloon pilots are managed by the Australian Ballooning Federation[64] and typically become members of regional hot air ballooning clubs. Commercial operations carrying fare paying passengers or charging for promotional flights must operate under an Air Operators Certificate from the Australian Civil Aviation and Safety Authority (CASA) with a nominated Chief Pilot. Pilots must have different degrees of experience before they are allowed to progress to larger balloons. Hot air balloons must be registered aircraft with CASA and are subject to regular airworthiness checks by authorised personnel.[65]
In the UK, the person in command must hold a valid Private Pilot's Licence issued by the Civil Aviation Authority specifically for ballooning; this is known as the PPL(B). There are two types of commercial balloon licences: CPL(B) Restricted and CPL(B) (Full). The CPL(B) Restricted is required if the pilot is undertaking work for a sponsor or being paid by an external agent to operate a balloon. The pilot can fly a sponsored balloon with everything paid for with a PPL unless asked to attend any event. Then a CPL(B) Restricted is required. The CPL(B) is required if the pilot is flying passengers for money. The balloon then needs a transport category C of A (certificate of air worthiness). If the pilot is only flying sponsor's guests and not charging money for flying other passengers, then the pilot is exempted from holding an AOC (air operator's certificate) though a copy of it is required.[clarification needed] For passenger flying the balloon also requires a maintenance log.
In the United States, a pilot of a hot air balloon must have a pilot certificate from the Federal Aviation Administration (FAA), carrying the rating of "Lighter-than-air free balloon", and unless the pilot is also qualified to fly gas balloons, will also carry this limitation: "Limited to hot-air balloons with airborne heater". A pilot does not need a license to fly an ultralight aircraft, but training is highly advised, and some hot-air balloons meet the criteria.
To carry paying passengers for hire (and attend some balloon festivals), a pilot must have a commercial pilot certificate. Commercial hot air balloon pilots may also act as hot air balloon flight instructors. While most balloon pilots fly for the pure joy of floating through the air, many are able to make a living as a professional balloon pilot. Some professional pilots fly commercial passenger sightseeing flights, while others fly corporate advertising balloons.[66]
The largest manufacturer of hot air balloons is Cameron Balloons of Bristol, England, which also owns Lindstrand Balloons of Oswestry, England. Cameron Balloons, Lindstrand Balloons and another English balloon manufacturing company Thunder and Colt (since acquired by Cameron) have been innovators and developers of special shaped balloons. These hot-air balloons use the same principle of lift as conventional inverted teardrop-shaped balloons, but often sections of the special balloon envelope shape do not contribute to the balloon's ability to stay aloft.
The second largest manufacturer of hot air balloons is Ultramagic company, based in Spain, which produces from 80 to 120 balloons per year. Ultramagic can produce very large balloons, such as the N-500 that accommodates as many as 27 persons in the basket, and has also produced many balloons with special shapes, as well as cold-air inflatables.
One of the three largest companies in the world is Kubicek Balloons. From its factory in Brno, Czechia the company ships its products worldwide. Produces from 100 to 115 balloons per year. Kubicek company also focus on special shape balloons, FAA/EASA type certified and are delivered with a Standard Airworthiness Certificate.
In the USA Aerostar International, Inc. of Sioux Falls, South Dakota was North America's largest balloon manufacturer and a close second in world manufacturing before ceasing to build balloons in January 2007. The oldest U.S. certified manufacturer is now Adams Balloons out of Albuquerque, New Mexico. Firefly Balloons, formerly The Balloon Works, is a manufacturer of hot air balloons in Statesville, North Carolina. Another manufacturer is Head Balloons, Inc. of Helen, Georgia.
The major manufacturers in Canada are Sundance Balloons and Fantasy Sky Promotions. Other manufacturers include Kavanagh Balloons of Australia, Schroeder Fire Balloons of Germany, Kubicek Balloons of the Czech Republic, and LLopis Balloons of France.
Propane tanks used in hot air balloons are mainly constructed of either aluminum or stainless steel. Most aluminum tanks are vertical 10-gallon cylinders (DOT 4E240), built primarily for forklift trucks.
Cylinders in liquid service are commonly found on forklifts.
2 Needle Double Lap Seaming Also called Felled Seam
all of the seams are the "French fell" type
The double lap seam features two rows of parallel stitching along the folded over fabric seam. A few manufactures use a flat seam.
perfect French Fell hot air balloon seam
Redirect to:
If weather conditions are unsafe, Hot Air Balloon Dubai flights are rescheduled or refunded according to policy.
Most Hot Air Balloon Dubai packages include hotel pickup, the balloon flight, safety briefing, and post-landing refreshments.
Hot Air Balloon Dubai experiences usually start early morning before sunrise, with hotel pickup around 4:00 AM to 5:00 AM.