Our Porta Punch is the fastest and most efficient way to punch out 13/16" round holes in 3/8” thick mild steel. It has a MAXIMUM Tensile Strength of 65,000 PSI.
Capable of processing a wide variety of holes with different specifications and shapes by simply adjusting the mold.
Some maintenance tips: Always clean the punch and die. Although they do not need lubrication, cleaning can extend their durability. Make use of only Enerpac Oil in both punch and pumps. Match punch and die appropriately at all times. For operations, ensure you set up dies with bigger openings to point downwards. Ensure you change cracked, chipped, or worn-out punches and dies immediately. Always observe the suited lifting force to avoid cracks while processing materials.
You can easily adjust the mold to fit different sizes and shapes of holes.
This tool is perfect for fast, hydraulic punching, and pneumatic feeding.
The 35-Ton hydraulic punching machine weighs 31 pounds and punches quickly. The dual-action remover holds the material and strips it so that you can punch the next hole in just seconds. It is suitable for punching railings, I-beams, tower iron, truck frames and truck frames. The maximum tensile strength is 65,000 Psi. Mount it to your work bench, or bring it to your job site. In less than 24 hours, rectangular, square or hex tools can be ordered.
Our single-acting hydraulic punches, which are portable and lightweight, are extensively used in the electrical industry, construction, as well as other outdoor work areas. It has a max punching thickness of approximately 16mm, a maximum punching diameter of 24mm, as well as a maximum throat height of 110mm.
Gulf States Saw & Machine Co. offers portable double-acting hydraulic punches that provide a complete mechanized process of punching and revert through its inbuilt dexterous control device along with inching (manual mode) and automatic load recognition.
Single-acting hydraulic punches can punch precise holes quickly and efficiently in a very short time. It has an automatic punch, returns and reset operation, which makes it suitable for many materials, including angle steel, channel and H-shapes steels and flat sheets (copper plate, aluminum and iron)
Hydraulic punches are designed to puncture metals using round, square, or oblong holes. They are designed to work on mild steel, nonferrous metals and non-shattering polymers.
Hydraulic bench press will reduce arm fatigue and speed up fabrication. The rugged 3/8-inch plate construction allows for a variety of uses. These dies are compatible with an H-Frame machine, hydraulic punch driver, as well as a 3/4-inch or 7/16 drawbol for dimpling PortaFab machine, which is Scotchman’s entry-level Ironworker. This unit packs 45 tons of hydraulic power and is portable 110 volt. It allows for the alignment of punches to punch thin sheet metal. This punch can also be used to punch spring steel for mounting race in order to punch angle iron. You can punch a hole within 9/16 inches of the web. The rotary-style punch can punch holes within 9/16 inches of the web. It also has enough power to punch hydraulic accessory ports on Edwards ironworkers. The punching time. It has a 4.5 second punching time, a jog down punch to ensure alignment and a power retractable punch. You can choose from 115 volt or a US...
You can adjust the tools quickly and it saves you a lot of time.
Gulf States Saw & Machine Co., a well-known distributor of a large range of single-acting portable hydraulic punches is designed with the highest quality materials and suitable for various industries.
The high coherence of the mechanized processing piece/product is outstanding, and the product quality is even more safe.
Remove a piece of aluminum foil. To sharpen the blades of a three-hole punch, make sure the foil is long enough to cover all three holes. Pull off enough to sharpen all of the punches at once for one-hole and decorative punches.
Punches are divided into two categories: hollow and solid. Hollow punches are used to create a hole by puncturing a surface such as sheet metal or leather. The "exit hole" near the working end of a hollow punch makes it easy to identify.
A punch is a tool used to make an indent or a hole in a hard surface. They are typically made of a hard metal rod with a narrow tip on one end and a broad flat "butt" on the other.